{"id":20989,"date":"2026-11-19T09:18:56","date_gmt":"2026-11-19T09:18:56","guid":{"rendered":"https:\/\/www.fibermall.com\/blog\/?p=20989"},"modified":"2026-11-19T09:18:58","modified_gmt":"2026-11-19T09:18:58","slug":"network-interface-card-nic-guide-speeds-and-ports","status":"publish","type":"post","link":"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm","title":{"rendered":"Network Interface Card (NIC) Guide: Speeds and Ports"},"content":{"rendered":"\n<p>A network interface card (NIC) is the adapter that connects a server or computer to a network. Choose a NIC based on four factors, in this order: port speed, port count, PCIe lane budget, and the optics or cables the port supports. Mistakes in the last two decisions can cost more than the card itself.<\/p>\n\n\n\n<p>That ordering isn&#8217;t the way most guides present it. Product listings lead with the controller name and headline speed because those are the easiest things to compare. But a NIC must match both the host&#8217;s PCIe capabilities and the network&#8217;s cabling infrastructure.<\/p>\n\n\n\n<p>Get the slot wrong and you throttle a card you paid for. Get the cage wrong and a module you already own won&#8217;t seat.<\/p>\n\n\n\n<p>This guide works through all four decisions from 1GbE to 800Gb\/s networking. It&#8217;s written for engineers specifying server hardware, so it favors lane counts, cage standards, and reach tables over definitions. Where a number matters, the number is here.<\/p>\n\n\n\n<div id=\"ez-toc-container\" class=\"ez-toc-v2_0_76 ez-toc-wrap-left counter-hierarchy ez-toc-counter ez-toc-grey ez-toc-container-direction\">\n<div class=\"ez-toc-title-container\">\n<p class=\"ez-toc-title\" style=\"cursor:inherit\">Table of Contents<\/p>\n<span class=\"ez-toc-title-toggle\"><a href=\"#\" class=\"ez-toc-pull-right ez-toc-btn ez-toc-btn-xs ez-toc-btn-default ez-toc-toggle\" aria-label=\"Toggle Table of Content\"><span class=\"ez-toc-js-icon-con\"><span class=\"\"><span class=\"eztoc-hide\" style=\"display:none;\">Toggle<\/span><span class=\"ez-toc-icon-toggle-span\"><svg style=\"fill: #999;color:#999\" xmlns=\"http:\/\/www.w3.org\/2000\/svg\" class=\"list-377408\" width=\"20px\" height=\"20px\" viewBox=\"0 0 24 24\" fill=\"none\"><path d=\"M6 6H4v2h2V6zm14 0H8v2h12V6zM4 11h2v2H4v-2zm16 0H8v2h12v-2zM4 16h2v2H4v-2zm16 0H8v2h12v-2z\" fill=\"currentColor\"><\/path><\/svg><svg style=\"fill: #999;color:#999\" class=\"arrow-unsorted-368013\" xmlns=\"http:\/\/www.w3.org\/2000\/svg\" width=\"10px\" height=\"10px\" viewBox=\"0 0 24 24\" version=\"1.2\" baseProfile=\"tiny\"><path d=\"M18.2 9.3l-6.2-6.3-6.2 6.3c-.2.2-.3.4-.3.7s.1.5.3.7c.2.2.4.3.7.3h11c.3 0 .5-.1.7-.3.2-.2.3-.5.3-.7s-.1-.5-.3-.7zM5.8 14.7l6.2 6.3 6.2-6.3c.2-.2.3-.5.3-.7s-.1-.5-.3-.7c-.2-.2-.4-.3-.7-.3h-11c-.3 0-.5.1-.7.3-.2.2-.3.5-.3.7s.1.5.3.7z\"\/><\/svg><\/span><\/span><\/span><\/a><\/span><\/div>\n<nav><ul class='ez-toc-list ez-toc-list-level-1 ' ><li class='ez-toc-page-1 ez-toc-heading-level-2'><a class=\"ez-toc-link ez-toc-heading-1\" href=\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm\/#Key_Takeaways\" >Key Takeaways<\/a><\/li><li class='ez-toc-page-1 ez-toc-heading-level-2'><a class=\"ez-toc-link ez-toc-heading-2\" href=\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm\/#What_Is_a_Network_Interface_Card\" >What Is a Network Interface Card?<\/a><\/li><li class='ez-toc-page-1 ez-toc-heading-level-2'><a class=\"ez-toc-link ez-toc-heading-3\" href=\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm\/#NIC_Port_Speeds_From_1GbE_to_800GbE\" >NIC Port Speeds From 1GbE to 800GbE<\/a><\/li><li class='ez-toc-page-1 ez-toc-heading-level-2'><a class=\"ez-toc-link ez-toc-heading-4\" href=\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm\/#The_Port_Is_Not_the_Pipe_PCIe_Lanes_and_Real_Throughput\" >The Port Is Not the Pipe: PCIe Lanes and Real Throughput<\/a><ul class='ez-toc-list-level-3' ><li class='ez-toc-heading-level-3'><a class=\"ez-toc-link ez-toc-heading-5\" href=\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm\/#Do_you_need_a_x16_card_for_25G\" >Do you need a x16 card for 25G?<\/a><\/li><\/ul><\/li><li class='ez-toc-page-1 ez-toc-heading-level-2'><a class=\"ez-toc-link ez-toc-heading-6\" href=\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm\/#Matching_the_Optic_to_the_Port\" >Matching the Optic to the Port<\/a><ul class='ez-toc-list-level-3' ><li class='ez-toc-heading-level-3'><a class=\"ez-toc-link ez-toc-heading-7\" href=\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm\/#Coded_modules_and_vendor_firmware\" >Coded modules and vendor firmware<\/a><\/li><li class='ez-toc-page-1 ez-toc-heading-level-3'><a class=\"ez-toc-link ez-toc-heading-8\" href=\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm\/#Reach_selection_by_speed\" >Reach selection by speed<\/a><\/li><li class='ez-toc-page-1 ez-toc-heading-level-3'><a class=\"ez-toc-link ez-toc-heading-9\" href=\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm\/#DAC_AOC_or_optic_the_cost_crossover\" >DAC, AOC, or optic: the cost crossover<\/a><\/li><li class='ez-toc-page-1 ez-toc-heading-level-3'><a class=\"ez-toc-link ez-toc-heading-10\" href=\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm\/#Breakout_and_fiber_budget\" >Breakout and fiber budget<\/a><\/li><\/ul><\/li><li class='ez-toc-page-1 ez-toc-heading-level-2'><a class=\"ez-toc-link ez-toc-heading-11\" href=\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm\/#Ethernet_InfiniBand_SmartNIC_and_DPU\" >Ethernet, InfiniBand, SmartNIC, and DPU<\/a><\/li><li class='ez-toc-page-1 ez-toc-heading-level-2'><a class=\"ez-toc-link ez-toc-heading-12\" href=\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm\/#How_to_Choose_a_Network_Interface_Card_for_a_Server\" >How to Choose a Network Interface Card for a Server<\/a><\/li><li class='ez-toc-page-1 ez-toc-heading-level-2'><a class=\"ez-toc-link ez-toc-heading-13\" href=\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm\/#Common_NIC_Selection_Failures\" >Common NIC Selection Failures<\/a><\/li><li class='ez-toc-page-1 ez-toc-heading-level-2'><a class=\"ez-toc-link ez-toc-heading-14\" href=\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm\/#FiberMall_NIC_Range_at_a_Glance\" >FiberMall NIC Range at a Glance<\/a><\/li><li class='ez-toc-page-1 ez-toc-heading-level-2'><a class=\"ez-toc-link ez-toc-heading-15\" href=\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm\/#Frequently_Asked_Questions\" >Frequently Asked Questions<\/a><ul class='ez-toc-list-level-3' ><li class='ez-toc-heading-level-3'><a class=\"ez-toc-link ez-toc-heading-16\" href=\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm\/#What_is_a_network_interface_card_used_for\" >What is a network interface card used for?<\/a><\/li><li class='ez-toc-page-1 ez-toc-heading-level-3'><a class=\"ez-toc-link ez-toc-heading-17\" href=\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm\/#Are_NIC_cards_still_used\" >Are NIC cards still used?<\/a><\/li><li class='ez-toc-page-1 ez-toc-heading-level-3'><a class=\"ez-toc-link ez-toc-heading-18\" href=\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm\/#What_is_the_difference_between_a_NIC_and_a_network_adapter\" >What is the difference between a NIC and a network adapter?<\/a><\/li><li class='ez-toc-page-1 ez-toc-heading-level-3'><a class=\"ez-toc-link ez-toc-heading-19\" href=\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm\/#Does_a_NIC_have_to_be_a_PCIe_card\" >Does a NIC have to be a PCIe card?<\/a><\/li><li class='ez-toc-page-1 ez-toc-heading-level-3'><a class=\"ez-toc-link ez-toc-heading-20\" href=\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm\/#What_is_the_fastest_NIC_available\" >What is the fastest NIC available?<\/a><\/li><li class='ez-toc-page-1 ez-toc-heading-level-3'><a class=\"ez-toc-link ez-toc-heading-21\" href=\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm\/#How_do_I_know_which_optic_my_NIC_accepts\" >How do I know which optic my NIC accepts?<\/a><\/li><\/ul><\/li><li class='ez-toc-page-1 ez-toc-heading-level-2'><a class=\"ez-toc-link ez-toc-heading-22\" href=\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm\/#Choosing_the_Right_Card_Starts_at_the_Port\" >Choosing the Right Card Starts at the Port<\/a><\/li><\/ul><\/nav><\/div>\n<h2 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"Key_Takeaways\"><\/span><strong>Key Takeaways<\/strong><strong><\/strong><span class=\"ez-toc-section-end\"><\/span><\/h2>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Port speed, port count, PCIe lane budget, and cage type are the four key decisions. Cage compatibility is often overlooked.<\/li>\n\n\n\n<li>A dual-100G card typically needs PCIe Gen4 x16; a single 100G port may fit Gen3 x16; and a dual-25G card generally fits Gen3 x8. Always check the adapter and server specifications.<\/li>\n\n\n\n<li>Many NIC deployment problems occur at the optical and cabling layer: unsupported modules, incorrect MPO polarity, and breakout plans with the wrong fiber count.<\/li>\n\n\n\n<li>FiberMall&#8217;s listed NIC range spans 1G to 800G-class connectivity, including the ConnectX-8, which supports 800Gb\/s InfiniBand XDR or configurable 2\u00d7400GbE.<\/li>\n\n\n\n<li>Price the port and its media, not just the card. Fiber count depends on the optical PMD: common 100G optics use 2 or 8 fibers, while 400G and 800G designs can use different counts.<\/li>\n<\/ul>\n\n\n\n<h2 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"What_Is_a_Network_Interface_Card\"><\/span><strong>What Is a Network Interface Card?<\/strong><strong><\/strong><span class=\"ez-toc-section-end\"><\/span><\/h2>\n\n\n\n<p>A network interface card is the hardware that lets a host communicate with a network. It contains a network controller, MAC and PHY functions, one or more physical cages, and a host interface such as PCIe or an OCP connector. The controller processes network traffic; the cage is where a transceiver or cable connector plugs in.<\/p>\n\n\n\n<p>Every network interface card you buy for a server resolves to those four parts. What changes between cards is how fast each part runs and what the cage accepts.<\/p>\n\n\n\n<p>That last part deserves emphasis because it&#8217;s where specifications get vague. A product page might say &#8220;dual-port 25G SFP28.&#8221; Read literally, that tells you three things: two ports, 25G per port, and SFP28 cages. It doesn&#8217;t tell you the PCIe lane requirement, whether the card is Gen3 or Gen4, or which 25G modules the firmware will accept. Those three unknowns decide whether the card works in your chassis.<\/p>\n\n\n\n<p>A network card also has a firmware and driver compatibility profile. Optical transceivers carry EEPROM identification data, including vendor and part information. Some host platforms accept third-party modules, while others may flag or reject them based on vendor-specific compatibility checks.<\/p>\n\n\n\n<p>This isn&#8217;t just a marketing detail. It can become a compatibility issue during installation.<\/p>\n\n\n\n<p>If you&#8217;d rather compare adapter types than work through selection logic, our <a href=\"https:\/\/www.fibermall.com\/blog\/fiber-network-card.htm\" target=\"_blank\"><u>fiber network card guide<\/u><\/a>&nbsp;covers SFP-based adapters in more detail.<\/p>\n\n\n\n<figure class=\"wp-block-image aligncenter size-full\"><img fetchpriority=\"high\" decoding=\"async\" width=\"800\" height=\"450\" src=\"https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2026\/11\/What-Is-a-Network-Interface-Card.png\" alt=\"What Is a Network Interface Card\" class=\"wp-image-20993\" srcset=\"https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2026\/11\/What-Is-a-Network-Interface-Card.png 800w, https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2026\/11\/What-Is-a-Network-Interface-Card-300x169.png 300w, https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2026\/11\/What-Is-a-Network-Interface-Card-768x432.png 768w\" sizes=\"(max-width: 800px) 100vw, 800px\" \/><\/figure>\n\n\n\n<h2 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"NIC_Port_Speeds_From_1GbE_to_800GbE\"><\/span><strong>NIC Port Speeds From 1GbE to 800GbE<\/strong><strong><\/strong><span class=\"ez-toc-section-end\"><\/span><\/h2>\n\n\n\n<p>A network card&#8217;s speed is set by the port, not by the controller&#8217;s peak rating, so the port is the first thing to check.<\/p>\n\n\n\n<p>The table below gives representative host-side electrical lane configurations and common optical PMDs. The electrical lane count is not necessarily the same as the optical lane count, and fiber count depends on the specific PMD.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><tbody><tr><td><strong>Speed<\/strong><strong><\/strong><\/td><td><strong>Typical host-side electrical lanes<\/strong><strong><\/strong><\/td><td><strong>Typical cage<\/strong><strong><\/strong><\/td><td><strong>Media<\/strong><strong><\/strong><\/td><td><strong>Common optical PMDs \/ cable types<\/strong><strong><\/strong><\/td><td><strong>Typical optical fiber count<\/strong><strong><\/strong><\/td><\/tr><tr><td>1G<\/td><td>1 \u00d7 1.25 Gb\/s NRZ<\/td><td>SFP<\/td><td>Copper or fiber<\/td><td>1000BASE-T, SX, LX, EX<\/td><td>2 for SX\/LX\/EX (duplex LC); copper uses RJ45<\/td><\/tr><tr><td>10G<\/td><td>1 \u00d7 10.3125 Gb\/s NRZ<\/td><td>SFP+<\/td><td>Fiber, DAC, or AOC<\/td><td>10GBASE-SR, LR, ER<\/td><td>2 for optical links (duplex LC)<\/td><\/tr><tr><td>25G<\/td><td>1 \u00d7 25.78125 Gb\/s NRZ<\/td><td>SFP28<\/td><td>Fiber, DAC, or AOC<\/td><td>25GBASE-SR, LR<\/td><td>2 for optical links (duplex LC)<\/td><\/tr><tr><td>40G<\/td><td>4 \u00d7 10.3125 Gb\/s NRZ<\/td><td>QSFP+<\/td><td>Fiber, DAC, or AOC<\/td><td>40GBASE-SR4, LR4<\/td><td>8 for SR4 (MPO-12); 2 for LR4 (duplex LC)<\/td><\/tr><tr><td>100G<\/td><td>Typically 4 \u00d7 25.78125 Gb\/s NRZ for QSFP28<\/td><td>QSFP28<\/td><td>Fiber, DAC, or AOC<\/td><td>100GBASE-SR4, LR4, ER4; DR1 variants<\/td><td>8 for SR4; 2 for LR4\/ER4\/DR1 (legacy SR10 uses 20)<\/td><\/tr><tr><td>200G<\/td><td>4 \u00d7 50 Gb\/s PAM4<\/td><td>QSFP56<\/td><td>Fiber, DAC, or AOC<\/td><td>200GBASE-SR4, DR4, FR4<\/td><td>8 for SR4\/DR4; 2 for FR4<\/td><\/tr><tr><td>400G<\/td><td>8 \u00d7 50G or 4 \u00d7 100G PAM4, depending on host interface<\/td><td>QSFP-DD or OSFP<\/td><td>Fiber, DAC, or AOC<\/td><td>400GBASE-SR8, DR4, FR4, LR4-6 \/ LR4-10<\/td><td>16 for SR8; 8 for DR4; 2 for FR4\/LR4<\/td><\/tr><tr><td>800G<\/td><td>8 \u00d7 100G Ethernet lanes or 4 \u00d7 200G XDR IB lanes, depending on protocol<\/td><td>QSFP-DD800 or OSFP<\/td><td>Fiber, DAC, or AOC<\/td><td>800GBASE-SR8, DR8, 2\u00d7FR4 \/ 2\u00d7LR4<\/td><td>16 for SR8\/DR8; 4 for 2\u00d7FR4\/2\u00d7LR4<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p>Three things in that table are worth pausing on.<\/p>\n\n\n\n<p>First, host-side electrical lanes and optical lanes must be treated separately. A QSFP28 100G interface commonly uses four 25G NRZ electrical lanes, while a 100G DR1 optical interface uses one 100G PAM4 optical lane. At 400G, a host interface using eight 50G PAM4 electrical lanes can connect to a DR4 or FR4 optical interface using four 100G PAM4 optical lanes. The exact mapping depends on the NIC, module, and PMD.<\/p>\n\n\n\n<p>Second, fiber count does not increase in a simple one-to-one relationship with port speed. A 100G SR4 link uses eight fibers, while common 100G LR4 and DR1 links use two. A 400G SR8 link uses 16 fibers, DR4 uses eight, and FR4 uses two. An 800G SR8\/DR8 link typically uses 16 fibers, while 2\u00d7FR4 uses four. Check the PMD and connector before sizing trunks and patch panels.<\/p>\n\n\n\n<p>Third, the cage column is where mechanical backward compatibility matters. SFP, SFP+, and SFP28 share a form factor, so many SFP28 ports can accept a 10G SFP+ module when the host supports 10G operation. QSFP+, QSFP28, and QSFP56 also share a form factor. QSFP-DD cages are designed to accept earlier QSFP-family modules, subject to host support and configuration.<\/p>\n\n\n\n<p>OSFP is a different, larger form factor and does not directly accept QSFP-family modules.<\/p>\n\n\n\n<p><strong>Note:<\/strong>&nbsp;Mechanical compatibility is necessary but not sufficient. A port may physically accept a module and still reject it in firmware or fail to support its speed, FEC mode, or link configuration. Check the datasheet for the specific NIC and module.<\/p>\n\n\n\n<p>Our<a href=\"https:\/\/www.fibermall.com\/store-17081-10gb-network-card.htm\" target=\"_blank\"><u>&nbsp;10G and 25G adapter<\/u><\/a>&nbsp;category and the 40G and 100G QSFP range both list the exact cage and PCIe generation for each card.<\/p>\n\n\n\n<figure class=\"wp-block-image aligncenter size-full\"><img decoding=\"async\" width=\"800\" height=\"450\" src=\"https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2026\/11\/The-Port-Is-Not-the-Pipe.png\" alt=\"The Port Is Not the Pipe\" class=\"wp-image-20994\" srcset=\"https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2026\/11\/The-Port-Is-Not-the-Pipe.png 800w, https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2026\/11\/The-Port-Is-Not-the-Pipe-300x169.png 300w, https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2026\/11\/The-Port-Is-Not-the-Pipe-768x432.png 768w\" sizes=\"(max-width: 800px) 100vw, 800px\" \/><\/figure>\n\n\n\n<h2 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"The_Port_Is_Not_the_Pipe_PCIe_Lanes_and_Real_Throughput\"><\/span><strong>The Port Is Not the Pipe: PCIe Lanes and Real Throughput<\/strong><strong><\/strong><span class=\"ez-toc-section-end\"><\/span><\/h2>\n\n\n\n<p>A NIC can only move as much data as its host slot allows. That sounds obvious. What is less obvious is that the lane arithmetic is rarely published, so teams buy by headline speed and discover the mismatch after install.<\/p>\n\n\n\n<p>Approximate PCIe bandwidth per lane, per direction (before transaction-layer overhead):<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><tbody><tr><td><strong>Generation<\/strong><strong><\/strong><\/td><td><strong>Per lane<\/strong><strong><\/strong><\/td><td><strong>x8 total<\/strong><strong><\/strong><\/td><td><strong>x16 total<\/strong><strong><\/strong><\/td><td><strong>Encoding<\/strong><strong><\/strong><\/td><\/tr><tr><td>Gen3<\/td><td>~985 MB\/s<\/td><td>~7.9 GB\/s<\/td><td>~15.8 GB\/s<\/td><td>128b\/130b<\/td><\/tr><tr><td>Gen4<\/td><td>~1.97 GB\/s<\/td><td>~15.8 GB\/s<\/td><td>~31.5 GB\/s<\/td><td>128b\/130b<\/td><\/tr><tr><td>Gen5<\/td><td>~3.94 GB\/s<\/td><td>~31.5 GB\/s<\/td><td>~63 GB\/s<\/td><td>128b\/130b<\/td><\/tr><tr><td>Gen6<\/td><td>~7.88 GB\/s<\/td><td>~63 GB\/s<\/td><td>~126 GB\/s<\/td><td>PAM4, FLIT, FEC\/CRC<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p>Converting those figures to network units gives the following practical guidelines. Compare the NIC&#8217;s aggregate one-direction port bandwidth with the PCIe bandwidth available in the same direction:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Dual 25G (50 Gb\/s aggregate) fits in Gen3 x8 (about 63 Gb\/s). This leaves roughly 20% of the PCIe link capacity unused before transaction-layer overhead.<\/li>\n\n\n\n<li>A single 100G port can fit in Gen3 x16 (about 126 Gb\/s), although the margin is limited. Check the NIC manufacturer&#8217;s recommended slot configuration.<\/li>\n\n\n\n<li>Dual 100G (200 Gb\/s aggregate) exceeds Gen3 x16 and generally requires Gen4 x16 (about 252 Gb\/s).<\/li>\n\n\n\n<li>A 400G port requires Gen5 x16 (about 504 Gb\/s) as a practical minimum. Gen4 x16 does not provide enough one-direction bandwidth.<\/li>\n\n\n\n<li>An 800G port requires Gen6 x16 (about 1,008 Gb\/s using the approximate figure in the table). Gen5 x16 is insufficient.<\/li>\n<\/ul>\n\n\n\n<p>A common failure mode is installing a faster-generation card in a slower-generation slot. A Gen4 card installed in a Gen3 slot typically negotiates at Gen3, reducing the available PCIe bandwidth. The system may still boot normally, but the host link can bottleneck the NIC when aggregate traffic exceeds the slot&#8217;s capacity.<\/p>\n\n\n\n<p>A realistic example is a dual-port 100G card installed in a Gen3 x16 slot. The two network ports offer 200 Gb\/s of aggregate one-direction bandwidth, but the PCIe link provides only about 126 Gb\/s. Under sustained aggregate load, the host interface can become the bottleneck. The remedy is a Gen4-capable path\u2014including the CPU root port, motherboard, and riser\u2014or a lower aggregate port configuration. A riser alone cannot upgrade a Gen3 root port to Gen4.<\/p>\n\n\n\n<p>One practical check before ordering: confirm the slot&#8217;s generation, not just its width. An x16 Gen3 slot and an x16 Gen4 slot can look identical from outside the chassis.<\/p>\n\n\n\n<figure class=\"wp-block-image aligncenter size-full\"><img decoding=\"async\" width=\"800\" height=\"450\" src=\"https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2026\/11\/Electrical-Lane-vs-Optical-Lane.png\" alt=\"Electrical Lane vs Optical Lane\" class=\"wp-image-20995\" srcset=\"https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2026\/11\/Electrical-Lane-vs-Optical-Lane.png 800w, https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2026\/11\/Electrical-Lane-vs-Optical-Lane-300x169.png 300w, https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2026\/11\/Electrical-Lane-vs-Optical-Lane-768x432.png 768w\" sizes=\"(max-width: 800px) 100vw, 800px\" \/><\/figure>\n\n\n\n<h3 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"Do_you_need_a_x16_card_for_25G\"><\/span><strong>Do you need a x16 card for 25G?<\/strong><strong><\/strong><span class=\"ez-toc-section-end\"><\/span><\/h3>\n\n\n\n<p>No. A dual-25G network interface card generally runs comfortably in an x8 Gen3 slot, provided the card and server support that configuration. This can leave an x16 slot available for a higher-bandwidth adapter later.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"Matching_the_Optic_to_the_Port\"><\/span><strong>Matching the Optic to the Port<\/strong><strong><\/strong><span class=\"ez-toc-section-end\"><\/span><\/h2>\n\n\n\n<p>This is the section most NIC guides omit, and it&#8217;s where the money and the failures are. A port speed tells you what the card can do. The cage and the optic tell you what it can connect to, over what distance, for what cost.<\/p>\n\n\n\n<p>For a server build, the module choice often costs more than the network interface card itself once you count one module per port plus the fiber between them.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"Coded_modules_and_vendor_firmware\"><\/span><strong>Coded modules and vendor firmware<\/strong><strong><\/strong><span class=\"ez-toc-section-end\"><\/span><\/h3>\n\n\n\n<p>Optical transceivers typically carry EEPROM identification data such as vendor name, OUI, part number, and supported capabilities. Some NIC platforms use firmware or driver policies to check this information and may flag or reject unsupported third-party modules. Other platforms are more permissive. Compatibility behavior varies by NIC model, firmware, driver, and module.<\/p>\n\n\n\n<p>A common symptom is a port that remains down or reports an unsupported-transceiver warning even though the module is seated and the link partner is operating normally. However, a link-down condition can also have other causes, including FEC mismatch, speed configuration, fiber polarity, or a faulty cable.<\/p>\n\n\n\n<p>The practical options are to order modules configured for the target platform or, where supported, to use a module with an appropriate compatibility profile. Reprogramming can improve compatibility, but it is not a universal guarantee or a substitute for checking the platform requirements. This is the purpose of FiberMall&#8217;s coding service.<\/p>\n\n\n\n<p>When requesting coding, provide the exact NIC or switch model, firmware\/software version where relevant, target port speed, and module part number\u2014not just the vendor name. Some platforms check more than a top-level vendor identifier.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"Reach_selection_by_speed\"><\/span><strong>Reach selection by speed<\/strong><strong><\/strong><span class=\"ez-toc-section-end\"><\/span><\/h3>\n\n\n\n<p>Reach is set by the module, and the module options narrow as speed rises. The table below lists representative reaches for common data-center optics. Exact reach depends on the PMD, fiber grade, channel loss, and product specification; check the datasheet for the specific part.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><tbody><tr><td><strong>Speed<\/strong><strong><\/strong><\/td><td><strong>Short reach<\/strong><strong><\/strong><\/td><td><strong>Mid reach<\/strong><strong><\/strong><\/td><td><strong>Long reach<\/strong><strong><\/strong><\/td><\/tr><tr><td>10G<\/td><td>SR: 300 m OM3, 400 m OM4<\/td><td>LR: 10 km<\/td><td>ER: 40 km<\/td><\/tr><tr><td>25G<\/td><td>SR: 70 m OM3, 100 m OM4<\/td><td>LR: 10 km<\/td><td>ER: uncommon<\/td><\/tr><tr><td>40G<\/td><td>SR4: 100 m OM3, 150 m OM4<\/td><td>LR4: 10 km<\/td><td>ER4: 40 km<\/td><\/tr><tr><td>100G<\/td><td>SR4: 70 m OM3, 100 m OM4; DR1: 500 m SMF<\/td><td>LR4: 10 km<\/td><td>ER4: 40 km<\/td><\/tr><tr><td>400G<\/td><td>SR8: about 100 m OM4; DR4: 500 m<\/td><td>FR4: 2 km<\/td><td>LR4-6: 6 km; LR4-10 MSA variants: 10 km<\/td><\/tr><tr><td>800G<\/td><td>SR8: about 100 m OM4; DR8: 500 m<\/td><td>FR4: 2 km<\/td><td>LR4: 10 km (where supported)<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p>Two patterns matter here. First, multimode reach generally decreases as signaling rates and PMD requirements increase. For example, 10GBASE-SR can reach 400 m on OM4, while 100GBASE-SR4 is typically limited to 100 m on OM4. If your campus or lab was built around OM3\/OM4 for 10G, do not assume the same cabling plant will support the same distances at 100G.<\/p>\n\n\n\n<p>Second, reach and fiber type depend on the PMD architecture, not simply the number of lanes. At 400G, SR8 uses parallel multimode fiber, DR4 uses parallel single-mode fiber, and FR4\/LR4 use wavelength multiplexing over duplex single-mode fiber. Do not compare SR8 and LR4 as if they were two single-mode options.<\/p>\n\n\n\n<figure class=\"wp-block-image aligncenter size-full\"><img loading=\"lazy\" decoding=\"async\" width=\"800\" height=\"450\" src=\"https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2026\/11\/Matching-the-Optic-to-the-Port.png\" alt=\"Matching the Optic to the Port\" class=\"wp-image-20996\" srcset=\"https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2026\/11\/Matching-the-Optic-to-the-Port.png 800w, https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2026\/11\/Matching-the-Optic-to-the-Port-300x169.png 300w, https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2026\/11\/Matching-the-Optic-to-the-Port-768x432.png 768w\" sizes=\"(max-width: 800px) 100vw, 800px\" \/><\/figure>\n\n\n\n<h3 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"DAC_AOC_or_optic_the_cost_crossover\"><\/span><strong>DAC, AOC, or optic: the cost crossover<\/strong><strong><\/strong><span class=\"ez-toc-section-end\"><\/span><\/h3>\n\n\n\n<p>Within a row, the choice between copper and optics is a distance and cost decision.<\/p>\n\n\n\n<p>Direct attach copper (DAC) is often the lowest-cost option for very short links, typically up to about 3 m for passive DAC and around 5 m for active DAC at 100G, depending on the product. It contains no optical components and does not require separate optical transceivers or optical-module burn-in. However, many DAC assemblies include EEPROM identification, and some platforms apply vendor-compatibility checks to cables as well.<\/p>\n\n\n\n<p>DAC is also thick and inflexible, which matters in dense racks.<\/p>\n\n\n\n<p>Active optical cables (AOC) are fiber with fixed ends. They reach further than DAC (commonly 20 to 100 m at 100G), bend more easily, and are immune to EMI. AOC costs more than DAC and less than a pair of modules plus a patch cord at short distances.<\/p>\n\n\n\n<p>Modules plus fiber are the flexible option and the right answer once you cross into structured cabling, patch panels, or any link you might repatch. They cost the most per link at short distances and the least per link once you are sharing trunk fiber across many ports.<\/p>\n\n\n\n<p>The crossover isn&#8217;t a fixed number, because it depends on your fiber plant and whether the module is coded. As a working rule, DAC wins inside a rack, AOC wins between adjacent racks up to about 30 m, and modules win beyond that or wherever you need structured cabling. The <a href=\"https:\/\/www.fibermall.com\/store-16527-dac-aoc-acc-aec-cables.htm\" target=\"_blank\"><u>DAC and AOC category lists<\/u><\/a>&nbsp;reach and gauge for each cable.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"Breakout_and_fiber_budget\"><\/span><strong>Breakout and fiber budget<\/strong><strong><\/strong><span class=\"ez-toc-section-end\"><\/span><\/h3>\n\n\n\n<p>High-speed ports can sometimes be split into lower-speed links. For example, a supported 400G port may be configured as 4\u00d7100G using a compatible breakout cable or breakout module. This is useful for connecting a high-density leaf port to four 100G servers. The NIC, switch, firmware, driver, transceiver, and cable must all support the intended breakout mode and lane mapping.<\/p>\n\n\n\n<p>Breakout changes the cabling plan. A 400G DR4 optical interface uses four 100G optical lanes and eight active fibers in an MPO-12 connector. A compatible breakout harness maps those fibers into four duplex pairs. The total active fiber count remains eight, but the connector layout, patch-panel mapping, and polarity plan change. MPO polarity errors\u2014where transmit and receive paths are not mapped correctly end to end\u2014are a common cause of physical-link failures in new builds.<\/p>\n\n\n\n<p><strong>Warning:<\/strong>&nbsp;Confirm polarity method (A, B, or C) for every MPO run before ordering trunk cables. A polarity mismatch produces the same symptom as a dead module and is harder to diagnose.<\/p>\n\n\n\n<figure class=\"wp-block-image aligncenter size-full\"><img loading=\"lazy\" decoding=\"async\" width=\"800\" height=\"450\" src=\"https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2026\/11\/DAC-AOC-or-Optic-The-Cost-Crossover.png\" alt=\"DAC, AOC, or Optic The Cost Crossover\" class=\"wp-image-20997\" srcset=\"https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2026\/11\/DAC-AOC-or-Optic-The-Cost-Crossover.png 800w, https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2026\/11\/DAC-AOC-or-Optic-The-Cost-Crossover-300x169.png 300w, https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2026\/11\/DAC-AOC-or-Optic-The-Cost-Crossover-768x432.png 768w\" sizes=\"(max-width: 800px) 100vw, 800px\" \/><\/figure>\n\n\n\n<h2 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"Ethernet_InfiniBand_SmartNIC_and_DPU\"><\/span><strong>Ethernet, InfiniBand, SmartNIC, and DPU<\/strong><strong><\/strong><span class=\"ez-toc-section-end\"><\/span><\/h2>\n\n\n\n<p>Four card families appear in server specifications, and they aren&#8217;t interchangeable.<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Ethernet NICs<\/strong>\u00a0carry Ethernet traffic, including TCP\/IP. When an application needs RDMA over Ethernet, RoCEv2 encapsulates RDMA transport over UDP\/IP and Ethernet; it is not a separate physical fabric alongside Ethernet and InfiniBand. Most data-center servers use Ethernet NICs, and the selection logic above applies directly.<\/li>\n\n\n\n<li><strong>InfiniBand host channel adapters<\/strong>\u00a0communicate over an InfiniBand fabric rather than Ethernet. They are common in AI and HPC clusters where the fabric is dedicated to GPU-to-GPU or other high-performance traffic. A card marketed as &#8220;VPI&#8221; (virtual protocol interconnect) may support either Ethernet or InfiniBand mode, depending on the model and configuration. Our InfiniBand optics collection covers the matching cable and module side.<\/li>\n\n\n\n<li><strong>SmartNICs<\/strong>\u00a0add programmable or specialized processing that can offload work from the host CPU, such as virtual switching, encryption, or storage processing. The value depends on the workload. A general-purpose web server may not benefit unless it has a specific offload requirement; a telco NFV host or a hypervisor running dense virtual switching may benefit substantially.<\/li>\n\n\n\n<li><strong>DPUs<\/strong>\u00a0extend the SmartNIC concept with an onboard compute complex, memory, and software environment. NVIDIA&#8217;s BlueField-3 is one example, and the company&#8217;s DOCA documentation describes its programming model.<\/li>\n<\/ul>\n\n\n\n<p>The selection question for a SmartNIC or DPU isn&#8217;t simply &#8220;is it faster?&#8221; It is &#8220;does the offload justify the added cost and operational complexity?&#8221; A DPU often costs more than a conventional NIC, adds a software stack to maintain, and needs a workload that can use its offload engines. For general-purpose servers, the benefit may be limited; for AI clusters, storage systems, or virtualized network functions with tight CPU budgets, it can be substantial.<\/p>\n\n\n\n<p>If the boundary between these categories is unclear for your design, our SmartNIC vs NIC comparison walks through where the offload line sits.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"How_to_Choose_a_Network_Interface_Card_for_a_Server\"><\/span><strong>How to Choose a Network Interface Card for a Server<\/strong><strong><\/strong><span class=\"ez-toc-section-end\"><\/span><\/h2>\n\n\n\n<p>Work the six steps in order. Each one constrains the next.<\/p>\n\n\n\n<ol class=\"wp-block-list\">\n<li><strong>Workload and protocol.<\/strong>\u00a0Decide whether the fabric will use Ethernet or InfiniBand. If you choose Ethernet and need RDMA, determine whether RoCEv2 is required. Everything downstream depends on this.<\/li>\n\n\n\n<li><strong>Port speed and count.<\/strong>\u00a0Match the NIC speed to the switch ports, then determine how many links are required. Two ports are common for redundancy, but the right count depends on the workload and topology.<\/li>\n\n\n\n<li><strong>PCIe budget.<\/strong>\u00a0Add the aggregate one-direction bandwidth of the NIC ports, then compare it with the available PCIe bandwidth. Confirm the slot generation, width, and actual lane allocation.<\/li>\n\n\n\n<li><strong>Cage and media.<\/strong>\u00a0Confirm the NIC&#8217;s cage and supported link modes, then choose a compatible transceiver or cable for both ends. The two ends do not always need identical cages; a supported breakout configuration may connect one high-speed port to multiple lower-speed ports.<\/li>\n\n\n\n<li><strong>Reach and fiber budget.<\/strong>\u00a0Select the optical PMD based on measured link distance, fiber type, channel loss, and margin. Count the active fibers required by that PMD before sizing trunks and patch panels.<\/li>\n\n\n\n<li><strong>Lifecycle.<\/strong>\u00a0Confirm driver support for your operating system and hypervisor, firmware update path, platform compatibility, and warranty. A card without a supported driver can become a future outage risk.<\/li>\n<\/ol>\n\n\n\n<p>That sequence front-loads the decisions that are expensive to reverse. Speed and protocol are hard to change later. Cage and reach are hard to change once cable is pulled.<\/p>\n\n\n\n<p>Our full network adapter range is organized by speed, which maps to step 2. Every card undergoes its own test and validation process before shipping, and the optical transceiver range covers step 4.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"Common_NIC_Selection_Failures\"><\/span><strong>Common NIC Selection Failures<\/strong><strong><\/strong><span class=\"ez-toc-section-end\"><\/span><\/h2>\n\n\n\n<p>These five account for most of the problems that reach a support queue.<\/p>\n\n\n\n<ol class=\"wp-block-list\">\n<li><strong>Unsupported transceiver or cable.<\/strong>\u00a0The platform flags or rejects a third-party optic or DAC. Check the exact NIC, firmware, driver, and module\/cable compatibility policy before ordering.<\/li>\n\n\n\n<li><strong>Dual-100G card in a Gen3 x16 slot.<\/strong>\u00a0The card may initialize normally, but the PCIe link&#8217;s available bandwidth (about 126 Gb\/s per direction) is below the two ports&#8217; 200 Gb\/s aggregate line rate. Confirm the slot generation and lane width before ordering.<\/li>\n\n\n\n<li><strong>OCP 3.0 module ordered for an incompatible chassis.<\/strong>\u00a0OCP NIC 3.0 uses a dedicated connector and mechanical interface; the server must have a compatible OCP 3.0 bay. Some 1U servers support it and others do not, so confirm the exact chassis configuration.<\/li>\n\n\n\n<li><strong>Incorrect MPO connector or polarity.<\/strong>\u00a0For example, an MPO-12 trunk may not match a port designed for MPO-16, or the polarity mapping may be wrong. Match the PMD, connector type, fiber count, and polarity method at both ends.<\/li>\n\n\n\n<li><strong>Thermal or airflow problems in a dense chassis.<\/strong>\u00a0A high-power NIC or transceiver installed in a shallow chassis with poor airflow may trigger thermal protection or lose link. Check the adapter&#8217;s and transceiver&#8217;s separate power and airflow requirements against the server design.<\/li>\n<\/ol>\n\n\n\n<h2 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"FiberMall_NIC_Range_at_a_Glance\"><\/span><strong>FiberMall NIC Range at a Glance<\/strong><strong><\/strong><span class=\"ez-toc-section-end\"><\/span><\/h2>\n\n\n\n<p>Prices below were verified on the product pages on November 18, 2026. Cards from 100G upward are quoted per configuration.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><tbody><tr><td><strong>Speed \/ mode<\/strong><strong><\/strong><\/td><td><strong>Model<\/strong><strong><\/strong><\/td><td><strong>Ports \/ configuration<\/strong><strong><\/strong><\/td><td><strong>Cage<\/strong><strong><\/strong><\/td><td><strong>PCIe<\/strong><strong><\/strong><\/td><td><strong>Price (USD)<\/strong><strong><\/strong><\/td><\/tr><tr><td>1G<\/td><td>Intel I210-F1<\/td><td>1<\/td><td>SFP<\/td><td>x1 v2.1<\/td><td>$60<\/td><\/tr><tr><td>1G<\/td><td>Intel 82576-F2<\/td><td>2<\/td><td>SFP<\/td><td>x4 v2.0<\/td><td>$68<\/td><\/tr><tr><td>1G<\/td><td>Intel I350-F4<\/td><td>4<\/td><td>SFP<\/td><td>x4 v2.1<\/td><td>$180<\/td><\/tr><tr><td>10G<\/td><td>Intel 82599EN-SR1<\/td><td>1<\/td><td>SFP+<\/td><td>x8 v2.0<\/td><td>$115<\/td><\/tr><tr><td>10G<\/td><td>Intel 82599ES-SR2<\/td><td>2<\/td><td>SFP+<\/td><td>x8 v2.0<\/td><td>$159<\/td><\/tr><tr><td>10G<\/td><td>Intel X710-BM2 DA2<\/td><td>2<\/td><td>SFP+<\/td><td>x8 v3.0<\/td><td>$179<\/td><\/tr><tr><td>10G<\/td><td>Intel XL710-BM1 DA4<\/td><td>4<\/td><td>SFP+<\/td><td>x8 v3.0<\/td><td>$309<\/td><\/tr><tr><td>25G<\/td><td>Intel XXV710-DA2<\/td><td>2<\/td><td>SFP28<\/td><td>x8 v3.0<\/td><td>$269<\/td><\/tr><tr><td>25G<\/td><td>Intel E810-XXVDA2<\/td><td>2<\/td><td>SFP28<\/td><td>x8 v4.0<\/td><td>Quote<\/td><\/tr><tr><td>25G<\/td><td>Intel E810-XXVDA4<\/td><td>4<\/td><td>SFP28<\/td><td>x16 v4.0<\/td><td>Quote<\/td><\/tr><tr><td>40G<\/td><td>Intel XL710-BM1 QDA1<\/td><td>1<\/td><td>QSFP+<\/td><td>x8 v3.0<\/td><td>$309<\/td><\/tr><tr><td>40G<\/td><td>Intel XL710 QDA2<\/td><td>2<\/td><td>QSFP+<\/td><td>x8 v3.0<\/td><td>Quote<\/td><\/tr><tr><td>100G<\/td><td>Intel E810-CQDA1<\/td><td>1<\/td><td>QSFP28<\/td><td>x16 v4.0<\/td><td>Quote<\/td><\/tr><tr><td>100G<\/td><td>Intel E810-CQDA2<\/td><td>2<\/td><td>QSFP28<\/td><td>x16 v4.0<\/td><td>Quote<\/td><\/tr><tr><td>200G<\/td><td>Intel E830CCAM1<\/td><td>1 x 200G or 2 x 100G<\/td><td>QSFP56<\/td><td>x8 v5.0<\/td><td>Quote<\/td><\/tr><tr><td>200G<\/td><td>NVIDIA ConnectX-6 MCX653105A-HDAT<\/td><td>1<\/td><td>QSFP56<\/td><td>x16 v4.0<\/td><td>Quote<\/td><\/tr><tr><td>400G<\/td><td>NVIDIA ConnectX-7 MCX75310AAS-NEAT<\/td><td>1<\/td><td>OSFP<\/td><td>x16 v5.0<\/td><td>Quote<\/td><\/tr><tr><td>800G IB XDR \/ 2\u00d7400GbE<\/td><td>NVIDIA ConnectX-8 C8180<\/td><td>1\u00d7800G InfiniBand or 2\u00d7400GbE Ethernet<\/td><td>OSFP<\/td><td>x16 v6.0<\/td><td>Quote<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p>Two notes on the range. The 10G and 25G cards share a category page because they share cages and use cases; the 10G\/25G listing explains the 10G-to-25G step. The listed 400G and 800G ConnectX models use OSFP cages, so they cannot directly accept QSFP28 modules from a 100G deployment. The Intel E830-CCAM1 is a controller; the physical port and cage arrangement depends on the adapter-board implementation. For the ConnectX-8 C8180, 800Gb\/s refers to the default InfiniBand XDR configuration; Ethernet operation supports two 400GbE ports when configured accordingly.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"Frequently_Asked_Questions\"><\/span><strong>Frequently Asked Questions<\/strong><strong><\/strong><span class=\"ez-toc-section-end\"><\/span><\/h2>\n\n\n\n<h3 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"What_is_a_network_interface_card_used_for\"><\/span><strong>What is a network interface card used for?<\/strong><strong><\/strong><span class=\"ez-toc-section-end\"><\/span><\/h3>\n\n\n\n<p>A network interface card connects a computer or server to a network and handles the conversion between the host&#8217;s internal data and the signals on the network medium. On a server it is the port your switch connects to.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"Are_NIC_cards_still_used\"><\/span><strong>Are NIC cards still used?<\/strong><strong><\/strong><span class=\"ez-toc-section-end\"><\/span><\/h3>\n\n\n\n<p>Yes, and they are more relevant on servers than on desktops, where the adapter is usually built into the motherboard. Server NICs are separate cards because they&#8217;re replaced and upgraded on a different schedule than the server itself.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"What_is_the_difference_between_a_NIC_and_a_network_adapter\"><\/span><strong>What is the difference between a NIC and a network adapter?<\/strong><strong><\/strong><span class=\"ez-toc-section-end\"><\/span><\/h3>\n\n\n\n<p>They describe the same hardware. &#8220;Network adapter&#8221; is the broader term and includes USB and wireless adapters; &#8220;NIC&#8221; usually implies an internal card with a physical network port. In server specifications the two are used interchangeably.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"Does_a_NIC_have_to_be_a_PCIe_card\"><\/span><strong>Does a NIC have to be a PCIe card?<\/strong><strong><\/strong><span class=\"ez-toc-section-end\"><\/span><\/h3>\n\n\n\n<p>No. It can be a PCIe add-in card, an OCP 3.0 module, a mezzanine card, or a LAN-on-motherboard implementation. OCP 3.0 is common in some hyperscale and enterprise server designs, but the chassis must include the matching OCP connector and mechanical bay; some 1U servers support it and others do not.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"What_is_the_fastest_NIC_available\"><\/span><strong>What is the fastest NIC available?<\/strong><strong><\/strong><span class=\"ez-toc-section-end\"><\/span><\/h3>\n\n\n\n<p>The highest rate depends on the protocol and configuration. In FiberMall&#8217;s listed range, NVIDIA ConnectX-8 C8180 supports 800Gb\/s InfiniBand XDR by default, or can be configured for two 400GbE Ethernet ports. It uses an OSFP cage and PCIe Gen6 x16; it is not a single-port 800GbE adapter. IEEE P802.3dj is progressing work on 1.6Tb\/s Ethernet, but 1.6TbE is not yet a mainstream server NIC option.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"How_do_I_know_which_optic_my_NIC_accepts\"><\/span><strong>How do I know which optic my NIC accepts?<\/strong><strong><\/strong><span class=\"ez-toc-section-end\"><\/span><\/h3>\n\n\n\n<p>Check three things in order: the cage standard (SFP28, QSFP28, OSFP), the module&#8217;s reach class (SR, LR, ER), and whether the card&#8217;s firmware accepts generic or only coded modules. The cage and reach are on the datasheet; the coding policy often requires asking the supplier.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\"><span class=\"ez-toc-section\" id=\"Choosing_the_Right_Card_Starts_at_the_Port\"><\/span><strong>Choosing the Right Card Starts at the Port<\/strong><strong><\/strong><span class=\"ez-toc-section-end\"><\/span><\/h2>\n\n\n\n<p>Four decisions set the outcome: port speed, port count, PCIe lane budget, and cage. Of these, the lane budget and physical interface are among the hardest to change after installation, yet product listings do not always explain them clearly.<\/p>\n\n\n\n<p>Work them in order and most selection risk disappears. Confirm the slot generation before the card ships. Confirm the cage standard before the modules ship. Confirm fiber count per port before the trunk cables are ordered.<\/p>\n\n\n\n<p>Each check takes minutes. Each one prevents a problem class that takes a maintenance window to correct.<\/p>\n\n\n\n<p>The optical layer isn&#8217;t a separate purchase from the NIC. It&#8217;s the same decision, made twice. Treat it that way and the card you buy is the card that performs.<\/p>\n\n\n\n<p>If you are specifying cards for a build, send us the chassis and switch port details and we will match the card, cage, and module together. Talk to our engineers or start from the network adapter range.<\/p>\n<style>\r\n\r\n        .lwrp.link-whisper-related-posts{\r\n            \r\n            margin-top: 40px;\nmargin-bottom: 30px;\r\n        }\r\n        .lwrp .lwrp-title{\r\n            \r\n            \r\n        }\r\n        .lwrp .lwrp-description{\r\n            \r\n            \r\n\r\n        }\r\n        .lwrp .lwrp-list-container{\r\n        }\r\n        .lwrp .lwrp-list-multi-container{\r\n            display: flex;\r\n        }\r\n        .lwrp .lwrp-list-double{\r\n            width: 48%;\r\n        }\r\n        .lwrp .lwrp-list-triple{\r\n            width: 32%;\r\n        }\r\n        .lwrp .lwrp-list-row-container{\r\n            display: flex;\r\n            justify-content: space-between;\r\n        }\r\n        .lwrp .lwrp-list-row-container .lwrp-list-item{\r\n            width: calc(100% - 20px);\r\n        }\r\n        .lwrp .lwrp-list-item:not(.lwrp-no-posts-message-item){\r\n            \r\n            list-style: decimal;\r\n        }\r\n        .lwrp .lwrp-list-item img{\r\n            max-width: 100%;\r\n            height: auto;\r\n        }\r\n        .lwrp .lwrp-list-item.lwrp-empty-list-item{\r\n            background: initial !important;\r\n        }\r\n        .lwrp .lwrp-list-item .lwrp-list-link .lwrp-list-link-title-text,\r\n        .lwrp .lwrp-list-item .lwrp-list-no-posts-message{\r\n            \r\n                \r\n        }\r\n        @media screen and (max-width: 480px) {\r\n            .lwrp.link-whisper-related-posts{\r\n                \r\n                \r\n            }\r\n            .lwrp .lwrp-title{\r\n                \r\n                \r\n            }\r\n            .lwrp .lwrp-description{\r\n                \r\n                \r\n            }\r\n            .lwrp .lwrp-list-multi-container{\r\n                flex-direction: column;\r\n            }\r\n            .lwrp .lwrp-list-multi-container ul.lwrp-list{\r\n                margin-top: 0px;\r\n                margin-bottom: 0px;\r\n                padding-top: 0px;\r\n                padding-bottom: 0px;\r\n            }\r\n            .lwrp .lwrp-list-double,\r\n            .lwrp .lwrp-list-triple{\r\n                width: 100%;\r\n            }\r\n            .lwrp .lwrp-list-row-container{\r\n                justify-content: initial;\r\n                flex-direction: column;\r\n            }\r\n            .lwrp .lwrp-list-row-container .lwrp-list-item{\r\n                width: 100%;\r\n            }\r\n            .lwrp .lwrp-list-item:not(.lwrp-no-posts-message-item){\r\n                \r\n                \r\n            }\r\n            .lwrp .lwrp-list-item .lwrp-list-link .lwrp-list-link-title-text,\r\n            .lwrp .lwrp-list-item .lwrp-list-no-posts-message{\r\n                \r\n                    \r\n            }\r\n        }<\/style>\r\n<div id=\"link-whisper-related-posts-widget\" class=\"link-whisper-related-posts lwrp\">\r\n            <h3 class=\"lwrp-title\">Related Posts<\/h3>    \r\n        <div class=\"lwrp-list-container\">\r\n                                            <ul class=\"lwrp-list lwrp-list-single\">\r\n                    <li class=\"lwrp-list-item\"><a href=\"https:\/\/www.fibermall.com\/blog\/spine-leaf-vs-traditional-three-tier.htm\" class=\"lwrp-list-link\"><span class=\"lwrp-list-link-title-text\">Spine-Leaf vs. Traditional Three-Tier Architecture: Comprehensive Comparison and Analysis<\/span><\/a><\/li><li class=\"lwrp-list-item\"><a href=\"https:\/\/www.fibermall.com\/blog\/800g-osfp-cable.htm\" class=\"lwrp-list-link\"><span class=\"lwrp-list-link-title-text\">Unlocking the Potential of 800G OSFP Cable Solutions: A Deep Dive into Compatibility and Performance<\/span><\/a><\/li><li class=\"lwrp-list-item\"><a href=\"https:\/\/www.fibermall.com\/blog\/qsfp56-dd.htm\" class=\"lwrp-list-link\"><span class=\"lwrp-list-link-title-text\">Understanding the Differences Between QSFP56-DD and Other Transceiver Modules: A Guide to 400G QSFP-DD Technology<\/span><\/a><\/li><li class=\"lwrp-list-item\"><a href=\"https:\/\/www.fibermall.com\/blog\/poe-network-switch.htm\" class=\"lwrp-list-link\"><span class=\"lwrp-list-link-title-text\">Everything You Need to Know About an 8-Port Gigabit PoE Network Switch<\/span><\/a><\/li><li class=\"lwrp-list-item\"><a href=\"https:\/\/www.fibermall.com\/blog\/market-forecast-for-aec-dac-aoc.htm\" class=\"lwrp-list-link\"><span class=\"lwrp-list-link-title-text\">Market Forecast for AEC, DAC, and AOC<\/span><\/a><\/li><li class=\"lwrp-list-item\"><a href=\"https:\/\/www.fibermall.com\/blog\/meraki-fiber-modules.htm\" class=\"lwrp-list-link\"><span class=\"lwrp-list-link-title-text\">Everything You Need to Know About Cisco Meraki Fiber Modules: A Complete Guide to SFP and Optic Transceivers<\/span><\/a><\/li><li class=\"lwrp-list-item\"><a href=\"https:\/\/www.fibermall.com\/blog\/usfp-vs-cpo.htm\" class=\"lwrp-list-link\"><span class=\"lwrp-list-link-title-text\">USFP vs CPO: Pluggable vs Co-Packaged Optics Compared<\/span><\/a><\/li><li class=\"lwrp-list-item\"><a href=\"https:\/\/www.fibermall.com\/blog\/800g-osfp.htm\" class=\"lwrp-list-link\"><span class=\"lwrp-list-link-title-text\">Exploring the Future of Connectivity: 800g OSFP Optical Transceiver<\/span><\/a><\/li><li class=\"lwrp-list-item\"><a href=\"https:\/\/www.fibermall.com\/news\/fiber-mall-silicon-photonics-transceiver.htm\" class=\"lwrp-list-link\"><span class=\"lwrp-list-link-title-text\">Fiber Mall Silicon Photonics Transceiver Project<\/span><\/a><\/li><li class=\"lwrp-list-item\"><a href=\"https:\/\/www.fibermall.com\/blog\/infiniband-price-guide-2026.htm\" class=\"lwrp-list-link\"><span class=\"lwrp-list-link-title-text\">InfiniBand Price Guide 2026: Switches, HCAs, Cables &amp; TCO<\/span><\/a><\/li><li class=\"lwrp-list-item\"><a href=\"https:\/\/www.fibermall.com\/blog\/400g-data-center-solution.htm\" class=\"lwrp-list-link\"><span class=\"lwrp-list-link-title-text\">400G Data Center Solution: Switches, Smart NICs and Optical Modules<\/span><\/a><\/li><li class=\"lwrp-list-item\"><a href=\"https:\/\/www.fibermall.com\/blog\/what-is-fttr.htm\" class=\"lwrp-list-link\"><span class=\"lwrp-list-link-title-text\">What is FTTR (Fiber to the Room)?<\/span><\/a><\/li>                <\/ul>\r\n                        <\/div>\r\n<\/div>","protected":false},"excerpt":{"rendered":"<p>A network interface card (NIC) is the adapter that connects a server or computer to a network. Choose a NIC based on four factors, in this order: port speed, port count, PCIe lane budget, and the optics or cables the port supports. Mistakes in the last two decisions can cost more than the card itself. [&hellip;]<\/p>\n","protected":false},"author":227,"featured_media":20990,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"_acf_changed":false,"site-sidebar-layout":"default","site-content-layout":"","ast-site-content-layout":"default","site-content-style":"default","site-sidebar-style":"default","ast-global-header-display":"","ast-banner-title-visibility":"","ast-main-header-display":"","ast-hfb-above-header-display":"","ast-hfb-below-header-display":"","ast-hfb-mobile-header-display":"","site-post-title":"","ast-breadcrumbs-content":"","ast-featured-img":"","footer-sml-layout":"","theme-transparent-header-meta":"","adv-header-id-meta":"","stick-header-meta":"","header-above-stick-meta":"","header-main-stick-meta":"","header-below-stick-meta":"","astra-migrate-meta-layouts":"set","ast-page-background-enabled":"default","ast-page-background-meta":{"desktop":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"ast-content-background-meta":{"desktop":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"footnotes":"","_wpscppro_dont_share_socialmedia":false,"_wpscppro_custom_social_share_image":0,"_facebook_share_type":"default","_twitter_share_type":"default","_linkedin_share_type":"default","_pinterest_share_type":"default","_linkedin_share_type_page":"default","_instagram_share_type":"default","_medium_share_type":"default","_threads_share_type":"default","_google_business_share_type":"default","_selected_social_profile":[{"id":"skM9ewvR8O","platform":"linkedin","platformKey":0,"name":"Jason Xue","type":"person","thumbnail_url":"https:\/\/media.licdn.com\/dms\/image\/C5603AQErPqKD0j6qBg\/profile-displayphoto-shrink_100_100\/0\/1599138392315?e=1723075200&v=beta&t=joEkh1OeKQ0F-QpAPv4xxQyBdGlHyccIQZauRSs6RvU","share_type":"default"}],"_wpsp_enable_custom_social_template":false,"_wpsp_social_scheduling":{"enabled":false,"datetime":null,"platforms":[],"status":"template_only","dateOption":"today","timeOption":"now","customDays":"","customHours":"","customDate":"","customTime":"","schedulingType":"absolute"},"_wpsp_active_default_template":true},"categories":[2,29],"tags":[],"class_list":["post-20989","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-blog","category-networking"],"acf":[],"yoast_head":"<!-- This site is optimized with the Yoast SEO Premium plugin v20.13 (Yoast SEO v25.8) - https:\/\/yoast.com\/wordpress\/plugins\/seo\/ -->\n<title>Network Interface Card (NIC) Guide: Speeds and Ports<\/title>\n<meta name=\"description\" content=\"Choose a network interface card by port speed, port count, PCIe lanes, and the optic the port accepts. Compare 1G to 800G server cards and their modules.\" \/>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm\" \/>\n<meta property=\"og:locale\" content=\"en_US\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"Network Interface Card (NIC) Guide: Speeds and Ports\" \/>\n<meta property=\"og:description\" content=\"A network interface card (NIC) is the adapter that connects a server or computer to a network. Choose a NIC based on four factors, in this order: port\" \/>\n<meta property=\"og:url\" content=\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm\" \/>\n<meta property=\"og:site_name\" content=\"fibermall.com\" \/>\n<meta property=\"article:published_time\" content=\"2026-11-19T09:18:56+00:00\" \/>\n<meta property=\"article:modified_time\" content=\"2026-11-19T09:18:58+00:00\" \/>\n<meta property=\"og:image\" content=\"https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2026\/11\/network-interface-card.png\" \/>\n\t<meta property=\"og:image:width\" content=\"900\" \/>\n\t<meta property=\"og:image:height\" content=\"600\" \/>\n\t<meta property=\"og:image:type\" content=\"image\/png\" \/>\n<meta name=\"author\" content=\"Catherine\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"Written by\" \/>\n\t<meta name=\"twitter:data1\" content=\"Catherine\" \/>\n\t<meta name=\"twitter:label2\" content=\"Est. reading time\" \/>\n\t<meta name=\"twitter:data2\" content=\"19 minutes\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\/\/schema.org\",\"@graph\":[{\"@type\":\"Article\",\"@id\":\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm#article\",\"isPartOf\":{\"@id\":\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm\"},\"author\":{\"name\":\"Catherine\",\"@id\":\"https:\/\/www.fibermall.com\/blog.htm\/#\/schema\/person\/bd2cf8d53f883c88f6ebaa5c3ed1258d\"},\"headline\":\"Network Interface Card (NIC) Guide: Speeds and Ports\",\"datePublished\":\"2026-11-19T09:18:56+00:00\",\"dateModified\":\"2026-11-19T09:18:58+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm\"},\"wordCount\":4011,\"publisher\":{\"@id\":\"https:\/\/www.fibermall.com\/blog.htm\/#organization\"},\"image\":{\"@id\":\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm#primaryimage\"},\"thumbnailUrl\":\"https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2026\/11\/network-interface-card.png\",\"articleSection\":[\"Blog\",\"Networking\"],\"inLanguage\":\"en-US\"},{\"@type\":\"WebPage\",\"@id\":\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm\",\"url\":\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm\",\"name\":\"Network Interface Card (NIC) Guide: Speeds and Ports\",\"isPartOf\":{\"@id\":\"https:\/\/www.fibermall.com\/blog.htm\/#website\"},\"primaryImageOfPage\":{\"@id\":\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm#primaryimage\"},\"image\":{\"@id\":\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm#primaryimage\"},\"thumbnailUrl\":\"https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2026\/11\/network-interface-card.png\",\"datePublished\":\"2026-11-19T09:18:56+00:00\",\"dateModified\":\"2026-11-19T09:18:58+00:00\",\"description\":\"Choose a network interface card by port speed, port count, PCIe lanes, and the optic the port accepts. Compare 1G to 800G server cards and their modules.\",\"breadcrumb\":{\"@id\":\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm#breadcrumb\"},\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm\"]}]},{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm#primaryimage\",\"url\":\"https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2026\/11\/network-interface-card.png\",\"contentUrl\":\"https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2026\/11\/network-interface-card.png\",\"width\":900,\"height\":600,\"caption\":\"network interface card\"},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\/\/www.fibermall.com\/blog.htm\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"Network Interface Card (NIC) Guide: Speeds and Ports\"}]},{\"@type\":\"WebSite\",\"@id\":\"https:\/\/www.fibermall.com\/blog.htm\/#website\",\"url\":\"https:\/\/www.fibermall.com\/blog.htm\/\",\"name\":\"fibermall.com\",\"description\":\"Optical Communication Expert\",\"publisher\":{\"@id\":\"https:\/\/www.fibermall.com\/blog.htm\/#organization\"},\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\/\/www.fibermall.com\/blog.htm\/?s={search_term_string}\"},\"query-input\":{\"@type\":\"PropertyValueSpecification\",\"valueRequired\":true,\"valueName\":\"search_term_string\"}}],\"inLanguage\":\"en-US\"},{\"@type\":\"Organization\",\"@id\":\"https:\/\/www.fibermall.com\/blog.htm\/#organization\",\"name\":\"fibermall.com\",\"url\":\"https:\/\/www.fibermall.com\/blog.htm\/\",\"logo\":{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\/\/www.fibermall.com\/blog.htm\/#\/schema\/logo\/image\/\",\"url\":\"https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2024\/12\/cropped-Fiber-Mall-Logo.jpg\",\"contentUrl\":\"https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2024\/12\/cropped-Fiber-Mall-Logo.jpg\",\"width\":200,\"height\":67,\"caption\":\"fibermall.com\"},\"image\":{\"@id\":\"https:\/\/www.fibermall.com\/blog.htm\/#\/schema\/logo\/image\/\"}},{\"@type\":\"Person\",\"@id\":\"https:\/\/www.fibermall.com\/blog.htm\/#\/schema\/person\/bd2cf8d53f883c88f6ebaa5c3ed1258d\",\"name\":\"Catherine\",\"image\":{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\/\/www.fibermall.com\/blog.htm\/#\/schema\/person\/image\/\",\"url\":\"https:\/\/secure.gravatar.com\/avatar\/3a11235a453567962b9c9bb843b31bb4396259dd8abad3f3c3758babd287d778?s=96&d=mm&r=g\",\"contentUrl\":\"https:\/\/secure.gravatar.com\/avatar\/3a11235a453567962b9c9bb843b31bb4396259dd8abad3f3c3758babd287d778?s=96&d=mm&r=g\",\"caption\":\"Catherine\"},\"description\":\"Optical Communications Engineer\",\"sameAs\":[\"https:\/\/www.fibermall.com\/\"],\"url\":\"https:\/\/www.fibermall.com\/blog.htm?author=227\"}]}<\/script>\n<!-- \/ Yoast SEO Premium plugin. -->","yoast_head_json":{"title":"Network Interface Card (NIC) Guide: Speeds and Ports","description":"Choose a network interface card by port speed, port count, PCIe lanes, and the optic the port accepts. Compare 1G to 800G server cards and their modules.","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm","og_locale":"en_US","og_type":"article","og_title":"Network Interface Card (NIC) Guide: Speeds and Ports","og_description":"A network interface card (NIC) is the adapter that connects a server or computer to a network. Choose a NIC based on four factors, in this order: port","og_url":"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm","og_site_name":"fibermall.com","article_published_time":"2026-11-19T09:18:56+00:00","article_modified_time":"2026-11-19T09:18:58+00:00","og_image":[{"width":900,"height":600,"url":"https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2026\/11\/network-interface-card.png","type":"image\/png"}],"author":"Catherine","twitter_card":"summary_large_image","twitter_misc":{"Written by":"Catherine","Est. reading time":"19 minutes"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"Article","@id":"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm#article","isPartOf":{"@id":"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm"},"author":{"name":"Catherine","@id":"https:\/\/www.fibermall.com\/blog.htm\/#\/schema\/person\/bd2cf8d53f883c88f6ebaa5c3ed1258d"},"headline":"Network Interface Card (NIC) Guide: Speeds and Ports","datePublished":"2026-11-19T09:18:56+00:00","dateModified":"2026-11-19T09:18:58+00:00","mainEntityOfPage":{"@id":"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm"},"wordCount":4011,"publisher":{"@id":"https:\/\/www.fibermall.com\/blog.htm\/#organization"},"image":{"@id":"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm#primaryimage"},"thumbnailUrl":"https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2026\/11\/network-interface-card.png","articleSection":["Blog","Networking"],"inLanguage":"en-US"},{"@type":"WebPage","@id":"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm","url":"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm","name":"Network Interface Card (NIC) Guide: Speeds and Ports","isPartOf":{"@id":"https:\/\/www.fibermall.com\/blog.htm\/#website"},"primaryImageOfPage":{"@id":"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm#primaryimage"},"image":{"@id":"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm#primaryimage"},"thumbnailUrl":"https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2026\/11\/network-interface-card.png","datePublished":"2026-11-19T09:18:56+00:00","dateModified":"2026-11-19T09:18:58+00:00","description":"Choose a network interface card by port speed, port count, PCIe lanes, and the optic the port accepts. Compare 1G to 800G server cards and their modules.","breadcrumb":{"@id":"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm#breadcrumb"},"inLanguage":"en-US","potentialAction":[{"@type":"ReadAction","target":["https:\/\/www.fibermall.com\/blog\/network-card-guide.htm"]}]},{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm#primaryimage","url":"https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2026\/11\/network-interface-card.png","contentUrl":"https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2026\/11\/network-interface-card.png","width":900,"height":600,"caption":"network interface card"},{"@type":"BreadcrumbList","@id":"https:\/\/www.fibermall.com\/blog\/network-card-guide.htm#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/www.fibermall.com\/blog.htm"},{"@type":"ListItem","position":2,"name":"Network Interface Card (NIC) Guide: Speeds and Ports"}]},{"@type":"WebSite","@id":"https:\/\/www.fibermall.com\/blog.htm\/#website","url":"https:\/\/www.fibermall.com\/blog.htm\/","name":"fibermall.com","description":"Optical Communication Expert","publisher":{"@id":"https:\/\/www.fibermall.com\/blog.htm\/#organization"},"potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/www.fibermall.com\/blog.htm\/?s={search_term_string}"},"query-input":{"@type":"PropertyValueSpecification","valueRequired":true,"valueName":"search_term_string"}}],"inLanguage":"en-US"},{"@type":"Organization","@id":"https:\/\/www.fibermall.com\/blog.htm\/#organization","name":"fibermall.com","url":"https:\/\/www.fibermall.com\/blog.htm\/","logo":{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/www.fibermall.com\/blog.htm\/#\/schema\/logo\/image\/","url":"https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2024\/12\/cropped-Fiber-Mall-Logo.jpg","contentUrl":"https:\/\/www.fibermall.com\/blog\/wp-content\/uploads\/2024\/12\/cropped-Fiber-Mall-Logo.jpg","width":200,"height":67,"caption":"fibermall.com"},"image":{"@id":"https:\/\/www.fibermall.com\/blog.htm\/#\/schema\/logo\/image\/"}},{"@type":"Person","@id":"https:\/\/www.fibermall.com\/blog.htm\/#\/schema\/person\/bd2cf8d53f883c88f6ebaa5c3ed1258d","name":"Catherine","image":{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/www.fibermall.com\/blog.htm\/#\/schema\/person\/image\/","url":"https:\/\/secure.gravatar.com\/avatar\/3a11235a453567962b9c9bb843b31bb4396259dd8abad3f3c3758babd287d778?s=96&d=mm&r=g","contentUrl":"https:\/\/secure.gravatar.com\/avatar\/3a11235a453567962b9c9bb843b31bb4396259dd8abad3f3c3758babd287d778?s=96&d=mm&r=g","caption":"Catherine"},"description":"Optical Communications Engineer","sameAs":["https:\/\/www.fibermall.com\/"],"url":"https:\/\/www.fibermall.com\/blog.htm?author=227"}]}},"_links":{"self":[{"href":"https:\/\/www.fibermall.com\/blog.htm\/index.php?rest_route=\/wp\/v2\/posts\/20989","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.fibermall.com\/blog.htm\/index.php?rest_route=\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.fibermall.com\/blog.htm\/index.php?rest_route=\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.fibermall.com\/blog.htm\/index.php?rest_route=\/wp\/v2\/users\/227"}],"replies":[{"embeddable":true,"href":"https:\/\/www.fibermall.com\/blog.htm\/index.php?rest_route=%2Fwp%2Fv2%2Fcomments&post=20989"}],"version-history":[{"count":2,"href":"https:\/\/www.fibermall.com\/blog.htm\/index.php?rest_route=\/wp\/v2\/posts\/20989\/revisions"}],"predecessor-version":[{"id":20998,"href":"https:\/\/www.fibermall.com\/blog.htm\/index.php?rest_route=\/wp\/v2\/posts\/20989\/revisions\/20998"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.fibermall.com\/blog.htm\/index.php?rest_route=\/wp\/v2\/media\/20990"}],"wp:attachment":[{"href":"https:\/\/www.fibermall.com\/blog.htm\/index.php?rest_route=%2Fwp%2Fv2%2Fmedia&parent=20989"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.fibermall.com\/blog.htm\/index.php?rest_route=%2Fwp%2Fv2%2Fcategories&post=20989"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.fibermall.com\/blog.htm\/index.php?rest_route=%2Fwp%2Fv2%2Ftags&post=20989"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}